Hammer Mill
Feed Mill, ,

Hammer Mill

Hammer mill is composed by Vein Feeder, Rotor, Screen, Shell and support, Motors and so on. Hammer mill mainly crush material by impact action. High speed rotation of hammer Collision with material ,ten material crushed. It is normally use for crush material in animal feed processing machine or grain flour producing. Slaved by main motor, the vein feeder introduces the material into hammer mill by controlling its flow. A series free-swing hammers assembled on the rotor run rapidly and smash the material into powder or grits into required size, with the help of gravity and air flow by external fans, the…
Read More
Additive Pre-Mixer
Feed Mill, ,

Additive Pre-Mixer

Part contact with material made by stainless steel, prevent of pollution of premix. Adopt advance technology and more than 10 years manufacture technology and experience. Cabinet and stirring shaft rotation in reverse direction, and paddles inter ensure adequate mixing of material. No residue, easy operation. Main parameter Model Volume(L) Weight (kg) Mixing time Power(kw) Mixing uniformity(CV) GH(SYTZ)50 50 25 6-10min(mixing time can extend according to material) 1.1 ≤5% GH(SYTZ)100 100 50 2.2 ≤5% GH(SYTZ)200 200 100 4 ≤5%  
Read More
Drum Sieve
Feed Mill, ,

Drum Sieve

QLYF Series cylindrical sieve used for raw material cleaning, can clean up wheat straw, stones ,rope, twigs, corn cobs these big impurities and dirty, sand, blighted grains these small impurities. Widely use in granary and feed factory. It also can use for milling, cereal, feed, oil, seeds, winery and silo storage as cleaning equipment. Feature: Big capacity, high efficiency, low energy, easy to install. Big and small impurities can clean by one machine. It can configure to different specifications of the screen according to different materials. Easy to maintenance.
Read More
Rotary Sifter
Feed Mill, ,

Rotary Sifter

1. It is use for screening and grading power or pellet feed, and classification for intermediate product after secondary pulverization. And it also can use for food, chemical, sugar, mining, paper and other industries in raw materials and finished screen and grading. 2. Selection emphasis on grading, sieve inertia force during movement in the horizontal direction to obtain a perfectly balanced. Small vibration and low noise. 3. Easy to installation. Replace sieve on the bottom, can greatly reduce area. Main Parameters Model SFJH56×2C SFJH80×2C SFJH110×2C SFJH130×2C SFJH150×2C Capacity (t/h) 1-3 5-8 8-10 10-15 17-22 Sieve size 900×560 1802×800 2002×1100 2200×1300…
Read More
Horizontal Ribbon Mixer
Feed Mill,

Horizontal Ribbon Mixer

It is conventional mixing machine, widely use in medium and small feed factory for compound feed mixing. With mixed time short, high efficiency, internal air circulation, low price. Main parameter HJJ40 HJJ50 HJJ71 HJJ80 HJJ112 Effective volume(cm3) 0.1 0.2 0.7 1 2 Batch mix Qty (kg) 50 100 250 500 1000 Batch mix time(min) 3-6 3-6 3-6 3-6 3-6 Mixing uniformity(CV) ≤7 ≤7 ≤7 ≤7 ≤7 Power (Kw) 0.75 2.2 4.0 7.5 15.0
Read More
Double-shaft Paddle Mixer
Feed Mill,

Double-shaft Paddle Mixer

Low speed, efficient mixing. Long time mixing does not produce segregation, with add liquid line. Double door discharge, less residue. Mixing time (45-90s), mixing evenness (CV≤5%) Suit for premixes, additives, feed, chemical and medicine…… Main parameters Model SJHJ0.2 SJHJ0.5 SJHJ1 SJHJ2 SJHJ3 SJHJ4 Effective volume(m3) 0.2 0.5 1 2 3 4 Batch mixing(KG) 100 250 500 1000 1500 2000 Batch mixing time(S) 45-90(The mixing time may be extended according to the material properties) Mixing evenness(CV) ≤5% ≤5% ≤5% ≤5% ≤5% ≤5% Power(kw) 2.2 5.5/7.5 11/15 18.5/22 22 30
Read More
Feed Counter Flow Cooler
Feed Mill,

Feed Counter Flow Cooler

The counter flow cooler adopts advanced technologies, combined with the current international advanced cooling technology developed by efficient alternative cooling equipment, mainly used for cooling high temperature pellet. Cooling system unique structure, cooling air and material flow relative, make pellets forward gradually cooling. Avoid part of high-temperature pellet difficult to dissipate heat in short time by vertical cooler. Pellet temperature not higher than room temperature after cooling. Precipitation rate not lower than 3.5%. Main parameter Model Capacity (t/h) Cooling time(min) Temperature after cool(℃) Suction volume(m3) Pressure (mmH-20) Blower SKLLN1.5 3 8-15 Not higher than room temperature 3-5℃ 28-34 200 4-72-11…
Read More
Feed Crumbler
Feed Mill

Feed Crumbler

Rolls adopt differential principle to crumble and shearing the big pellet to irregularly small pellet.Roll protection device ensure roll can automatic avoidance when encountered hard foreign material. Bypass device can pass material when no need crumble. High efficiency, low noise and long working life. Widely use for feed pellets crumble, also suit for soya, maize or soft mineral. Main parameter Type SSLG15×80 SSLG15×100 SSLG15×150 SSLG20×170 Capacity(t/h) 2-4 3-6 8-15 15-20 Roll size ф 150×800 ф 150×1000 ф 150×1500 ф 200×1700 Power(kw) 4 5.5 7.5 11 Roll(pc) 2 2 2/3 3  
Read More
Pellet Mill
Feed Mill,

Pellet Mill

Pellet mill (Granulator)  is a feed processing machine which can directly compress powder into pellet. Our feed pellet mill mainly composed by stepless speed regulation feeder, conditioner, pelleting device, driven and security system. Dual-motor driving system, can suppression step by step. Smooth rotation, low noise, high output and easy operation and maintenance. Suit for high quality livestock and poultry, aquatic feed, organic fertilizer, fertilizer granulation and other materials. Quick release ring mold, ring mold lifting device can be configured. Main Parameter Model Capacity(t/h) Power(kw) Inner Dia. Of Die(mm) SZLH-15 0.1-0.2 3KW ∮150 SZLH-20 0.5-0.7 11KW ∮200 SZLH-30 1-3 2×15KW ∮300…
Read More
Feed Grinding Section
Feed Mill, ,

Feed Grinding Section

Feed raw material contains different particle size and if mixed directly will do nothing for helping the nutrition of the final products. According to different particle size of the feed raw material, one time or two times grinding should be adopted accordingly. By grinding, the particle of raw material will be in average size and mixed in some degree, and it will be more suitable for further mixing and pelleting. For Grinding, hammer mill is the main equipment to do this work. Following is the rough grinding flow:  
Read More